SLRI Machine Status Accelerator Operation Cryogenics
  Accelerator E-Logbook, Page 1 of 83  Not logged in Accelerator E-Logbook
ID Date Author Event Time Type Section Icon Subject Status RTime (min)
  6569   Sun 07 Jul 2019 19:15:38 Apiwat Pinyoyang Sun 07 Jul 2019 14:04:11 ProblemElectrical Warning Beam dump @135 mA / Electrical unstableFixed 

14:04 Beam dump @135 mA / Electrical unstable
          - Linac, Y-BM-M, Y-QF-M, Y-QD-M, Y-KM-M fault
          - H-BV-M1, H-BH-M1, H-BV-M2, H-BH-M2 fault
          - S-BMP-M2, S-BM-M fault
          - S-QF-L1-SW, S-QD-L2-SW fault

          Reset => OK

15:26 Warm up LBT, SYN and HBT magnets.

15:51 Warm up STR magnet.

17:07 Start injection (max rate = 14 mA/min)

17:25 Stop injection @150 mA

17:28 Set parameter for store and close MPW gap completed.

  6568   Sun 07 Jul 2019 08:57:14 Apiwat Pinyoyang Sun 07 Jul 2019 08:05:26 Beam OperationMachine Operation Note Beam Injection Completed 

07:40 Test run syn >>> OK. (Isyn = 10 mA)

08:05 Warm up HBT magnet, set parameter, open MPW gap.

08:06 Stop SOFB @ 81.86 mA

08:09 Beam drop from 81 to 46 mA during set parameter.

08:11 Start injection (Max rate = 16 mA/min)

08:22 Stop injection @ 150 mA

08:25 Set parameter for store and close MPW gap complete.

Attachment 1: SOFB_2019-07-07-0800.PNG
SOFB_2019-07-07-0800.PNG
  6567   Sun 07 Jul 2019 08:53:46 Apiwat Pinyoyang Sat 06 Jul 2019 18:50:52 Beam OperationMachine Operation Note Beam Injection Completed 

18:50 Warm up HBT magnet, set parameter, open MPW gap.

18:57 Beam drop from 104.18 to 44.58 mA during set parameter

19:00 Start injection (Max rate = 10 mA/min)

19:15 Stop injection @ 150.21 mA

19:18 Set parameter for store and close MPW gap complete.

  6566   Sun 07 Jul 2019 08:50:15 Apiwat Pinyoyang Sat 06 Jul 2019 12:48:43 Beam OperationMachine Operation Note Beam Injection Completed 

12:48 Warm up HBT, Set parameter and Open MPW gap.

12:51 Start injection (Max rate = 11.6 mA/min)

13:00 Stop injection @ 150 mA

  6565   Sat 06 Jul 2019 08:04:49 Nitisart Kumdee Sat 06 Jul 2019 08:00:34 Beam OperationMachine Operation Note Beam Injection Completed 

07:32 Test run SYN >> OK (ISYN = 15 mA).

08:02 Stop SOFB @ 79.47 mA.

08:03 Warm up HBT, set parameter for beam injection and open MPW gap.

08:08 Start injection (max rate = 11.46 mA/min).

08:18 Stop injection @ 150.03  mA.

08:21 Set parameter for store and close MPW gap completed.

08:23 SOFB completed @ 148.98 mA

Attachment 1: SOFB_2019-07-06-0801.PNG
SOFB_2019-07-06-0801.PNG
  6564   Fri 05 Jul 2019 20:04:33 Nitisart Kumdee Fri 05 Jul 2019 20:00:02 Beam OperationMachine Operation Note Beam Injection Completed 

19:34 Test run SYN => OK (ISYN = 15 mA)

20:02 Stop SOFB @ 77.78 mA

20:03 Warm up HBT, set parameter for injection, open MPW gap

20:07 Beam drop from 73.79 mA to 36.33 mA after start injection / Human error - forget load STR parameter by manual.

20:09 Re-Start injection (Max rate = 12 mA/min)

20:24 Stop injection @ 150.10  mA

20:27 Set parameter for beam store and close MPW gap completed

20:29 SOFB completed @ 149.03 mA

Attachment 1: SOFB_2019-07-05-2002.PNG
SOFB_2019-07-05-2002.PNG
  6563   Fri 05 Jul 2019 09:23:36 Thapakron Pulampong Fri 05 Jul 2019 09:23:21 Measured ParameterBeam Dynamics Note Parameter Before shutdown 2019Under Process 

Parameter collection

Date  05072019

Time 09:27

Beam current :   138.0537 mA

Parameter collection before annual shutdown

MODE 6 operation(U60+MPW+  SMPW)

---------------------------------------------------------------------------------------------------------------

 

+ Hardware check

'HWtable_2019-7-5_9-24.mat'

 

+ Orbit w.r.t reference

 

+ Physics parameter check

B:\TP\matlabPro\machineCheck\physicsCheck

 'PHYtable_2019-7-5_9-28.mat'

BL measurement 

 

PBPM                2019 06 10                        2019 07 05

PBPM            -724.222222151419    -703.375869492136
PBPM            -985.975761223580    -1207.30331379647
PBPM            -798.240041003820    -817.527821444439
PBPM            -363.348774957849    -482.576078935616
PBPM            22.8304375939131    92.3711641403141
PBPM            -142.651742474781    -69.9944858430129
PBPM            -1103.73842278934    -272.474340612531
PBPM            764.193806591168    3.45646721416923
PBPM            -96.9184605466331    148.489941302184
PBPM            0    0
PBPM            0    0
PBPM            -893.436657050385    -854.721197367833

 

 

+ SOFB program ----------------------------------------------------------------------------------------------------------------------------------

SPS Orbit Control System - v7.1.20190503

ONLINE reference for SOFB

 

+ Beam profile

 

 

 

 

  6562   Fri 05 Jul 2019 08:16:40 Chanwawit Somprasong Fri 05 Jul 2019 08:00:34 Beam OperationMachine Operation Note Beam Injection Completed 

07:27 Test run SYN >> OK (ISYN = 12 mA).

08:00 Stop SOFB @ 79.47 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap.

08:05 Start injection (max rate = 15.4 mA/min).

08:12 Stop injection @ 150.4  mA.

08:15 Set parameter for store and close MPW gap completed.

08:17 SOFB completed @ 148 mA

Attachment 1: SOFB_2019-07-05-0755.PNG
SOFB_2019-07-05-0755.PNG
  6561   Thu 04 Jul 2019 20:24:16 Nitisart Kumdee Thu 04 Jul 2019 20:10:26 Beam OperationMachine Operation Note Beam Injection Completed 

19:04  BL-8 request time 10 min.

20:10 Stop SOFB @ 77.80 mA

20:11 Warm up HBT, set parameter for injection, open MPW gap

20:15 Beam drop from 71.91 mA to 43.64 mA after start injection

20:18 Re-Start injection (Max rate = 12 mA/min; Ave rate = 10 mA/min)

20:25 Beam drop from 114.68 mA to 96.35 mA during injection.

20:32 Stop injection @ 150.41 mA

20:35 Set parameter for beam store , close MPW gap completed

20:37 SOFB completed @ 149.19 mA

Attachment 1: SOFB_2019-07-04-2010.PNG
SOFB_2019-07-04-2010.PNG
  6560   Thu 04 Jul 2019 08:22:21 Nitisart Kumdee Thu 04 Jul 2019 08:10:09 Beam OperationMachine Operation Note Beam Injection Completed 

07:30 Test run SYN >> OK (ISYN = 12 mA).

07:34 BL8 request time 10 min

08:10 Stop SOFB @ 78.41 mA.

08:11 Warm up HBT, set parameter for beam injection and open MPW gap. 

08:12 Beam drop from 77 mA to 73 mA (-4 mA/min) during set parameter for injection.

08:15 Start injection (max rate = 10.6 mA/min).

08:24 Stop injection @ 150.02  mA.

08:27 Set parameter for store and close MPW gap completed.

08:30 SOFB completed @ 148.90 mA

Attachment 1: SOFB_2019-07-04-0810.PNG
SOFB_2019-07-04-0810.PNG
  6559   Wed 03 Jul 2019 20:33:36 Chanwawit Somprasong Wed 03 Jul 2019 20:10:24 Beam OperationMachine Operation Note Beam Injection Completed 

19:17 Test run SYN => OK (ISYN = 20 mA)

19:50  BL-8 request time 10 min.

20:10 Stop SOFB @ 77.71 mA

20:11 Warm up HBT, set parameter for injection, open MPW gap

20:14 Start injection (Max rate = 10.2 mA/min)

20:26 Stop injection @ 150.25 mA

20:29 Set parameter for beam store , close MPW gap completed

20:31 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-07-03-2006.PNG
SOFB_2019-07-03-2006.PNG
  6558   Wed 03 Jul 2019 08:23:21 Chanwawit Somprasong Wed 03 Jul 2019 08:00:09 Beam OperationMachine Operation Note Beam Injection Completed 

07:18 Test run SYN >> OK (ISYN = 20 mA).

08:00 Stop SOFB @ 77.29 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap. , beam drop (-2.66mA ) , (-7.82mA) during set parameter 

08:04 Start injection (max rate = 16 mA/min).

08:18 Stop injection @ 150.4  mA.

08:22 Set parameter for store and close MPW gap completed.

08:24 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-07-03-0758.PNG
SOFB_2019-07-03-0758.PNG
  6557   Tue 02 Jul 2019 20:30:17 Apiwat Pinyoyang Tue 02 Jul 2019 20:00:58 Beam OperationMachine Operation Note Beam Injection Completed 

19:40 Test run SYN => OK (ISYN = 15 mA)

20:00 Stop SOFB @ 103 mA

20:01 Warm up HBT, set parameter for injection, open MPW gap

20:03 Beam drop from 103 to 96 mA during set parameter for injection.

20:05 Start injection (Max rate = 10.6 mA/min)

20:26 Stop injection @ 147.8  mA

20:28 Set parameter for beam store and close MPW gap completed

20:30 SOFB completed @ 145.6 mA

Attachment 1: SOFB_2019-07-02-1955.PNG
SOFB_2019-07-02-1955.PNG
  6556   Tue 02 Jul 2019 14:24:47 Apiwat Pinyoyang Tue 02 Jul 2019 12:00:21 Beam OperationMachine Operation Note Beam Injection Completed133

12:00 Power ON system.

12:54 Warm up magnet LBT, SYN, HBT, STR.

13:16 Test run syn >>> OK.

13:40 Re warm up HBT magnet.

13:45 Start injection no beam.

13:47 Warm up ID Magnet Initializer.

13:55 Start injection (Max rate = 16.9 mA/min).

14:08 Stop injection @ 150.5 mA.

14:11 Set parameter for store and close MPW gap complete.

14:13 SOFB complete @ 149.2 mA.

  6555   Tue 02 Jul 2019 14:14:55 Apiwat Pinyoyang Tue 02 Jul 2019 05:00:17 OtherElectrical Idea Dump beamFixed 

04:55 BL-1.1 request time 10 min.

05:10 Dump beam @ 89 mA

05:14 Power off magnet STR and SYN.

06:00 Electrical power OFF due to  PEA maintenance.

06:25 Electrical main incomming from PEA ON / Can't ON Ring main unit at SW.gear room.

07:00 Call team service from Schneider.

10:45 Checking machanic of ring main unit by team service.

11:40 Eletrical system power on.

 

  6554   Mon 01 Jul 2019 20:18:18 Apiwat Pinyoyang Mon 01 Jul 2019 20:10:03 Beam OperationMachine Operation Note Beam Injection Completed 

19:24 BL-8 request time 10 min.

19:40 Test run SYN => OK (ISYN = 10 mA)

20:10 Stop SOFB @ 76 mA

20:11 Warm up HBT, set parameter for injection, open MPW gap

20:12 Beam drop from 76 to 66 mA during set parameter for injection.

20:15 Start injection (Max rate = 8.7 mA/min)

20:27 Stop injection @ 150  mA

20:29 Set parameter for beam store and close MPW gap completed

20:32 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-07-01-2005.PNG
SOFB_2019-07-01-2005.PNG
  6553   Mon 01 Jul 2019 08:18:54 Chanwawit Somprasong Mon 01 Jul 2019 08:18:38 Beam OperationMachine Operation Note Beam Injection Completed 

07:10Test run SYN >> OK (ISYN = 10 mA).

08:00 Stop SOFB @ 77.76 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap. , beam drop (-14.46 mA ) during set parameter @ 63 mA

08:03 Start injection (max rate = 10.9 mA/min).

08:13 Stop injection @ 150  mA.

08:15 Set parameter for store and close MPW gap completed.

08:18 SOFB completed @ 148.8 mA

Attachment 1: SOFB_2019-07-01-0756.PNG
SOFB_2019-07-01-0756.PNG
  6552   Sun 30 Jun 2019 20:28:43 Apiwat Pinyoyang Sun 30 Jun 2019 20:10:31 Beam OperationMachine Operation Note Beam Injection Completed 

19:35 Test run SYN => OK (ISYN = 12 mA)

19:36 BL-8 request time 10 min

20:10 Stop SOFB @ 75.8 mA

20:11 Warm up HBT, set parameter for injection, open MPW gap

20:12 Beam drop from 75 to 73 mA during set parameter for injection.

20:15 Start injection (Max rate = 11 mA/min)

20:24 Stop injection @ 150  mA

20:27 Set parameter for beam store and close MPW gap completed

20:30 SOFB completed @ 148.8 mA

Attachment 1: SOFB_2019-06-30-2005.PNG
SOFB_2019-06-30-2005.PNG
  6551   Sun 30 Jun 2019 08:20:51 Somkiat Wisaiphion Sun 30 Jun 2019 08:00:31 Beam OperationMachine Operation Note Beam Injection   

07:40 Test run SYN >> OK (ISYN = 10 mA).

08:00 Stop SOFB @ 78.5 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap.

08:05 Start injection (max rate = 10.5 mA/min).

08:13 Stop injection @ 150  mA.

08:16 Set parameter for store and close MPW gap completed.

08:19 SOFB completed @ 148.8 mA

Attachment 1: SOFB_2019-06-30-0800.PNG
SOFB_2019-06-30-0800.PNG
  6550   Sat 29 Jun 2019 20:29:55 Somkiat Wisaiphion Sat 29 Jun 2019 20:10:39 Beam OperationMachine Operation Note Beam Injection   

19:45 Test run SYN => OK (ISYN = 12 mA)

19:30 BL-8 request time 10 min

20:10 Stop SOFB @ 75.8 mA

20:11 Warm up HBT, set parameter for injection, open MPW gap

20:15 Start injection (Max rate = 10.8 mA/min)

20:22 Stop injection @ 150  mA

20:26 Set parameter for beam store and close MPW gap completed

20:28 SOFB completed @ 148.8 mA

Attachment 1: SOFB_2019-06-29-2010.PNG
SOFB_2019-06-29-2010.PNG
  6549   Sat 29 Jun 2019 08:17:12 Somkiat Wisaiphion Sat 29 Jun 2019 08:00:56 Beam OperationMachine Operation Note Beam Injection   

07:20 Test run SYN >> OK (ISYN = 10 mA).

08:00 Stop SOFB @ 78.5 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap.

08:05 Start injection (max rate = 11 mA/min).

08:13 Stop injection @ 150  mA.

08:16 Set parameter for store and close MPW gap completed.

08:18 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-06-29-0800.PNG
SOFB_2019-06-29-0800.PNG
  6548   Fri 28 Jun 2019 08:47:14 Somkiat Wisaiphion Fri 28 Jun 2019 08:00:58 Beam OperationMachine Operation Note Beam Injection   

07:30 Test run SYN >> OK (ISYN = 10 mA).

08:00 Stop SOFB @ 78 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap.

08:07 Start injection (max rate = 10 mA/min).

08:41 Stop injection @ 150  mA.

08:43 Set parameter for store and close MPW gap completed.

08:45 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-06-28-0800.PNG
SOFB_2019-06-28-0800.PNG
  6547   Thu 27 Jun 2019 20:42:35 Somkiat Wisaiphion Thu 27 Jun 2019 20:00:17 Beam OperationMachine Operation Note Beam Injection   

19:35 Test run SYN => OK (ISYN = 12 mA)

19:45 BL-1.2 request time 15 min

20:15 Stop SOFB @ 77.1 mA

20:16 Warm up HBT, set parameter for injection, open MPW gap

20:20 Start injection (Max rate = 8.9 mA/min)

20:35 Stop injection @ 150  mA

20:38 Set parameter for beam store and close MPW gap completed

20:40 SOFB completed @ 148 mA

  6546   Thu 27 Jun 2019 08:06:29 Apiwat Pinyoyang Thu 27 Jun 2019 08:00:26 Beam OperationMachine Operation Note Beam Injection Completed 

07:30 Test run SYN >> OK (ISYN = 12 mA).

08:00 Stop SOFB @ 77.9 mA.

08:01 Warm up HBT, set parameter for beam injection and open MPW gap. 

08:02 Beam drop from 79 mA to 67 mA (-12 mA/min) during set parameter for injection.

08:05 Start injection (max rate = 10.6 mA/min).

08:14 Stop injection @ 150  mA.

08:17 Set parameter for store and close MPW gap completed.

08:20 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-06-27-0755.PNG
SOFB_2019-06-27-0755.PNG
  6545   Wed 26 Jun 2019 21:03:22 Chanwawit Somprasong Wed 26 Jun 2019 20:10:41 Beam OperationMachine Operation Warning Y-QD-M Fault , Dump beam Completed6

19:23 Test run SYN  Y-QD-M fault ( hybrid_wd )

19:48 BL-8 request time 10 min.

20:21 Dump beam @ 77 mA due to check water leakage in STR 

20:33 Warm up HBT, set parameter for injection, open MPW gap , test run SYN = OK (Isyn = 12 mA)

20:41 Start injection (Max rate = 10 mA/min)

20:56 Stop injection @ 150.4 mA

20:59 Set parameter for beam store , close MPW gap completed

21:01SOFB completed @ 149.41 mA

Attachment 1: Y-QD-M_fault_(26_june_2019).PNG
Y-QD-M_fault_(26_june_2019).PNG
  6544   Wed 26 Jun 2019 08:09:17 Apiwat Pinyoyang Wed 26 Jun 2019 08:10:55 Beam OperationMachine Operation Note Beam Injection Completed 

00:00 BL-8 request time 10 min

07:40 Test run SYN >> OK (ISYN = 12 mA).

08:10 Stop SOFB @ 77.9 mA.

08:11 Warm up HBT, set parameter for beam injection and open MPW gap. 

08:12 Beam drop from 77 mA to 67 mA (-10 mA/min) during set parameter for injection.

08:15 Start injection (max rate = 10.6 mA/min).

08:24 Stop injection @ 150  mA.

08:27 Set parameter for store and close MPW gap completed.

08:30 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-06-26-0805.PNG
SOFB_2019-06-26-0805.PNG
  6543   Tue 25 Jun 2019 20:12:52 Apiwat Pinyoyang Tue 25 Jun 2019 20:05:38 Beam OperationMachine Operation Note Beam Injection Completed 

19:35 Test run SYN => OK (ISYN = 12 mA)

19:50 BL-1.1 request time 5 min

20:05 Stop SOFB @ 79.1 mA

20:06 Warm up HBT, set parameter for injection, open MPW gap

20:07 Beam drop from 79 mA to 69 mA (-10 mA/min) during set parameter for injection.

20:10 Start injection (Max rate = 11.5 mA/min)

20:18 Stop injection @ 150.3  mA

20:21 Set parameter for beam store and close MPW gap completed

20:23 SOFB completed @ 149.3 mA

Attachment 1: SOFB_2019-06-25-2000.PNG
SOFB_2019-06-25-2000.PNG
  6542   Tue 25 Jun 2019 08:44:51 Apiwat Pinyoyang Tue 25 Jun 2019 08:10:38 Beam OperationMachine Operation Note Beam Injection Completed 

07:30 Test run SYN >> OK (ISYN = 10mA).

07:40 BL-8 request time 10 min

08:10 Stop SOFB @ 77.8 mA.

08:11 Warm up HBT, set parameter for beam injection and open MPW gap. 

08:16 Start injection (max rate = 11 mA/min).

08:38 Stop injection @ 150  mA.

08:41 Set parameter for store and close MPW gap completed.

08:43 SOFB completed @ 149 mA

Attachment 1: SOFB_2019-06-25-0805.PNG
SOFB_2019-06-25-0805.PNG
  6541   Mon 24 Jun 2019 20:22:30 Apiwat Pinyoyang Mon 24 Jun 2019 20:10:18 Beam OperationMachine Operation Note Beam Injection Completed 

18:50 BL-1.2 request time 10 min

19:36 Test run SYN => OK (ISYN = 10 mA)

20:10 Stop SOFB @ 97 mA

20:11 Warm up HBT, set parameter for injection, open MPW gap

20:13 Beam drop from 97 mA to 69 mA (-27 mA/min) during set parameter for injection.

20:15 Start injection (Max rate = 11 mA/min)

20:26 Stop injection @ 150  mA

20:29 Set parameter for beam store and close MPW gap completed

20:31 SOFB completed @ 149.26 mA

Attachment 1: SOFB_2019-06-24-2005.PNG
SOFB_2019-06-24-2005.PNG
  6540   Mon 24 Jun 2019 16:33:30 Chanwawit Somprasong Mon 24 Jun 2019 15:55:03 Beam OperationMachine Operation Warning Beam dumpCompleted37

15:55 Beam dump @ 95 mA 

           -   RF fault ( NIG-RF carvity 1 )

           -   inter lock vaccurm hight occurred

16:00 Warm up HBT , set parameter for injection , open MPW gap

16:10 Start injection ( max rate = 11 mA/min)

16:27 Stop injection @ 120 mA

16:30 Set parameter for ceam store , close MPW gap

16:32 SOFB completed @ 119.76 mA

Attachment 1: 2019-06-24_Beam_dump_1555.png
2019-06-24_Beam_dump_1555.png
Attachment 2: 2019-06-24_Beam_Trip.PNG
2019-06-24_Beam_Trip.PNG
Accelerator Technology Division | Synchrotron Light Research Institute (Public Organization) | Powered by ELOG V3.1.1